ACADLSPASDOC |
Determines whether the icad.lsp file is loaded for every .dwg file when it is opened. |
ACADPREFIX |
Displays the search path stored by the SRCHPATH system variable. |
ACADVER |
Stores the version number. Required for .dwg file compatibility only. |
ACISLICENSE |
Stores whether ACIS is supported and available in the user interface. |
ACISOUTVER |
Not implemented. Required for .dwg file compatibility only. |
ACTRECPATH |
Sets the default path used to search for and store new action macros. |
AECAUTOUPDATE |
Determines whether two-dimensional views update automatically when section lines or elevation lines change. |
AECOBJECTS |
Determines whether AEC objects are read and displayed. |
AFLAGS |
Stores attribute flags for the ATTDEF command. |
ALLOWSYNCOUT |
Controls synchronous output at the command line. |
ANGBASE |
Specifies the zero base angle relative to the current user coordinate system (UCS). |
ANGDIR |
Sets the orientation of the positive direction relative to the active user coordinate system (UCS). |
ANNOALLVISIBLE |
Determines the display of annotative entities that do not support the current scale. |
ANNOAUTOSCALE |
Determines whether all annotative entities are assigned the current annotation scale automatically when it is set. |
ANNOSCALELIMIT |
Determines the number of annotation scales that a drawing can have before a warning message displays. |
ANNOTATIVEDWG |
Not implemented. Required for .dwg file compatibility only. |
APBOX |
Turns on and off the display of the aperture cursor when you use entity snaps. |
APERTURE |
Sets the entity snap selection area in pixels. |
APERTURECOLOR |
Controls the color of the entity snap selection box. |
ARRAYASSOCIATIVITY |
Determines whether new arrays are created as a set of associative or independent entities. |
ARRAYBLOCKNAME |
Stores the name of the array that is currently being edited. |
ARRAYTYPE |
Determines what type of array is created by default when using the Array command. |
AREA |
Stores the last area calculated by commands such as LIST or AREA. |
ARTISANLICENSE |
Stores whether ARTISAN is supported and available in the user interface. |
ASYNCINIT |
Controls whether components within IntelliCAD can be loaded simultaneously or one at a time. |
ASYNCSELECT |
Controls whether the cursor moves independently from the entity snap, and therefore more freely, in large drawings or drawings with large blocks. |
ATTDIA |
Controls whether attribute value entries are processed via a dialog box or command line prompt. |
ATTIPE |
Not implemented. Required for .dwg file compatibility only. |
ATTMODE |
Turns the display of attributes on or off (visible or invisible), or maintains their active assigned state. |
ATTMULTI |
Not implemented. Required for .dwg file compatibility only. |
ATTREQ |
Controls whether default attribute settings are used during insertion of blocks. |
AUDIONOTETOOLTIP |
Turns on or off the display of audio note tooltips. |
AUDITCTL |
Controls whether a report is generated while recovering or auditing a drawing file. |
AUNITS |
Sets the unit of measurement for angles. |
AUPREC |
Sets the decimal precision for angular units. |
AUTOCOMPLETEFILTER |
Controls which items are included in the list of suggested names displayed in the AutoComplete window. |
AUTOCOMPLETEMODE |
Controls the AutoComplete feature for the command line and for File dialogs. |
AUTOCOMPLETEOPTIONS |
Controls various options for how command names are suggested and displayed when typing in the command bar. |
AUTOCOMPLETEDELAY |
Controls the number of milliseconds to wait between keystrokes before displaying the AutoComplete window. |
AUTOCOMPLETETRANSP |
Controls the transparency of the AutoComplete window. |
AUTOCOMPMINTEXTLEN |
Controls the number of letters to be typed in the command bar before displaying the AutoComplete window. |
AUTOCONVERT |
Determines the dialog boxes that display when converting a .dwg file from version 2013 to 2010. |
AUTODWFPUBLISH |
Not implemented. Required for .dwg file compatibility only. |
AUTOMATICPUB |
Determines whether a .dwf or .pdf file is created automatically when a .dwg file is saved or closed. |
AUTOMENULOAD |
When you open a drawing, determines whether the default menu or a menu file associated with a drawing is loaded. |
AUTOPUBLISHPATH |
Stores the path used to save .dwf and .pdf files that can be created automatically when .dwg files are saved or closed. |
AUTOSAVERETAIN |
Controls how autosave (.sv$) and backup (.bak) files are treated when a drawing file or the program is closed. |
AUTOSNAP |
Controls the use of fly-over snap markers, aperture box, snap tooltips, tracking, and snap magnet. |
AUTOTRACKCOLOR |
Determines the color of polar and entity snap tracking paths. |
AXISMODE |
Not implemented. Required for .dwg file compatibility only. |
CACHEMAXFILES |
Determines the maximum number of graphics cache files that can be saved. |
CACHEMAXTOTALSIZE |
Determines the maximum size (in bytes) of the graphics cache files. |
CAMERADISPLAY |
Determines whether camera icons display in the drawing. |
CAMERAHEIGHT |
Specifies the default height assigned to new cameras. |
CANNOSCALE |
Determines the current annotation scale for the Model tab or a layout viewport on a Layout tab. |
CANNOSCALEVALUE |
Stores the value of the current annotation scale. |
CDATE |
Stores calendar date and time based on a Julian calendar. |
CECOLOR |
Assigns a color to new entities without changing the color of existing entities. |
CELTSCALE |
Stores the linetype scale for entities. |
CELTYPE |
Stores the linetype of new entities. |
CELWEIGHT |
Stores the lineweight of new entities. |
CENTERCROSSGAP |
Not implemented. Required for .dwg file compatibility only. |
CENTERCROSSSIZE |
Not implemented. Required for .dwg file compatibility only. |
CENTEREXE |
Not implemented. Required for .dwg file compatibility only. |
CENTERLAYER |
Not implemented. Required for .dwg file compatibility only. |
CENTERLTSCALE |
Not implemented. Required for .dwg file compatibility only. |
CENTERLTYPE |
Not implemented. Required for .dwg file compatibility only. |
CENTERLTYPEFILE |
Not implemented. Required for .dwg file compatibility only. |
CENTERMARKEXE |
Not implemented. Required for .dwg file compatibility only. |
CETRANSPARENCY |
Specifies the default transparency for new entities. |
CGEOCS |
Stores the name of the GIS coordinate system that is assigned to the current drawing. |
CHAMFERA |
Stores the first chamfer distance associated with the distance-distance method. |
CHAMFERB |
Stores the second chamfer distance associated with the distance-distance method. |
CHAMFERC |
Stores the distance of the chamfer associated with the distance-angle method. |
CHAMFERD |
Stores the angle of the chamfer associated with the distance-angle method. |
CHAMMODE |
Determines whether the chamfer is created based on the input of two distances or an angle and a distance. |
CIPMODE |
Not implemented. Required for .dwg file compatibility only. |
CIRCLERAD |
Stores the default radius for circle. |
CLAYER |
Stores the active layer. |
CLEANSCREENSTATE |
Reports the state of the clean screen, which is the result of the Clean Screen On command. |
CLINELAYER |
Stores the name of the layer that construction lines are drawn on. |
CMATERIAL |
Not implemented. Required for .dwg file compatibility only. |
CMDACTIVE |
Stores the information specifying whether a script, dialog box, command, or transparent command is active. |
CMDDIA |
Controls whether dialog boxes are turned on for commands. |
CMDECHO |
Toggles echoing on (debug mode) or off (run mode) when using the AutoLISP function. |
CMDLINEKEYWORDBKGCOLOR |
Determines the background color of keywords in the command bar. |
CMDLNTEXT |
Changes the command line word or symbol indicating that the program is ready for a command. |
CMDNAMES |
Shows the name of the command or transparent command in use. |
CMLEADERSTYLE |
Not implemented. Required for .dwg file compatibility only. |
CMLJUST |
Not implemented. Required for .dwg file compatibility only. |
CMLSCALE |
Not implemented. Required for .dwg file compatibility only. |
CMLSTYLE |
Not implemented. Required for .dwg file compatibility only. |
COLORX |
Controls the color of the x-axis in the user coordinate system (UCS) icon and cursor crosshair. |
COLORXBEDITOR |
Controls the color of the x-axis in the user coordinate system (UCS) icon and cursor crosshair in the Block Editor. |
COLORY |
Controls the color of the y-axis in the user coordinate system (UCS) icon and cursor crosshair. |
COLORYBEDITOR |
Controls the color of the y-axis in the user coordinate system (UCS) icon and cursor crosshair in the Block Editor. |
COLORZ |
Controls the color of the z-axis in the user coordinate system (UCS) icon and cursor crosshair. |
COLORZBEDITOR |
Controls the color of the z-axis in the user coordinate system (UCS) icon and cursor crosshair in the Block Editor. |
COMPASS |
Determines whether the 3D compass is turned on or off in the current viewport. |
COORDS |
Controls the update of coordinates on the status line. |
COPYMODE |
Controls whether the Copy command prompts for multiple copies automatically. |
CPLOTSTYLE |
Sets the current print style for new entities. |
CROSSHAIRMODE |
Controls whether the cursor displays as a regular crosshairs or a gunsight crosshairs.
|
CSHADOW |
Not implemented. Required for .dwg file compatibility only. |
CTAB |
Controls whether the Model tab or a specified layout tab displays in the drawing window. |
CURRENTAFFINITYMASK |
Reports a bit code representing which CPUs are currently being used by IntelliCAD. |
CURSORMODE |
Determines whether the cursor color changes when the cursor moves over entities or areas that have the same color. |
CURSORSIZE |
Specifies the size of the crosshairs cursor display. |
CURSORTYPE |
Determines how the pointer is displayed. |
CUSTOMICONSPATH |
Stores the path used to locate user defined icons and bitmaps for custom menus. |
CVPORT |
Sets the current viewport's identification number. To change the current viewport, the identification number specified must be for an active viewport. |
DASHBOARDSTATE |
Not implemented. Required for .dwg file compatibility only. |
DATALINKNOTIFY
|
Not implemented. Required for .dwg file compatibility only. |
DATE |
Stores the current system date and time. |
DBCSTATE |
Not implemented. Required for .dwg file compatibility only. |
DBMOD |
Stores the drawing modification status using bit-code to indicate the current status. |
DCTCUST |
Stores the path and file name of the custom spelling dictionary. |
DCTMAIN |
Stores the file name of the main spelling dictionary. |
DCTMAINPATH |
Stores the path of the main spelling dictionary. |
DEFAULTLIGHTING |
Determines whether default lighting is kept on or off when other lighting types are turned on. |
DEFAULTLIGHTINGINTENSITY |
Sets the intensity percentage for default lighting. |
DEFAULTLIGHTINGTYPE |
Sets the type of default lighting. |
DEFLPLSTYLE |
Displays information about the default print style that is assigned to layer zero in new drawings or older drawings when you open them. |
DEFPLSTYLE |
Displays information about the default print style that is assigned to new entities in new drawings or older drawings when you open them. |
DEFPLSTYLETBL |
Displays the name of the print style table type that is used by new drawings or older drawings when you open them.
|
DEFSAVEASTYPEINDEX |
Determines the default version of .dwg files in the Save As dialog box.
|
DELOBJ |
Controls the ability for you to retain or delete entities used to create other entities. For example, MIRROR and MIRROR3D are two commands that use this variable to retain or delete the original mirrored entity. |
DEMANDLOAD |
Determines when applications are demand-loaded. |
DGNCURRENTLTSCALEVALUE
|
Stores the current DGN linetype scale.
|
DGNDESIGNSCALE
|
Determines the current linetype scale when DGNLTSCALEMODE is set to 1 (annotation linetype scale).
|
DGNFRAME |
Determines whether DGN frames are visible and printed. |
DGNIMPORTMAX |
Sets the limit for the number of converted elements when importing a .dgn file. |
DGNLTSCALEMODE
|
Determines which type of scale is used for the current DGN linetype scale.
|
DGNLTYPESELECTIVEREGEN
|
Controls whether entities assigned DGN linetypes (DGN0-DGN7) are automatically regenerated when zooming.
|
DGNOSNAP |
Determines whether entity snapping is turned on or off for .dgn files that are attached to drawings. |
DGNWORKSPACE |
Stores the name of the workspace that is activated when opening or creating a .dgn drawing. |
DGNWORKSPACEAUTOSWITCH |
Controls whether the workspace changes automatically when you switch between .dwg and .dgn files. |
DIASTAT |
Stores information about the method used to exit the most recently used dialog box. |
DIMADEC |
Determines the number of decimal places used for displaying angular dimension text. |
DIMALT |
Controls the ability to use alternate unit systems in dimensions in addition to the default units. |
DIMALTD |
Sets the number of decimal places used in alternate units. |
DIMALTF |
Specifies the scale factor for alternate units. |
DIMALTRND |
Determines rounding of alternate dimension units. |
DIMALTTD |
Controls the number of decimal places for alternate unit tolerances. |
DIMALTTZ |
Controls the suppression of zeros in limits or tolerances included as part of alternate dimensions. |
DIMALTU |
Specifies the text format for alternate units. |
DIMALTZ |
Turns on and off the suppression of zeros for alternate unit dimensions. |
DIMANNO |
Reports whether the current dimension style is annotative. |
DIMAPOST
|
Specifies the prefix and/or suffix that appears in alternate unit dimension text. |
DIMARCSYM
|
Specifies the location of the dimension arc length symbol. |
DIMASO |
No longer used, but supported for .dwg file compatibility. |
DIMASSOC |
Controls whether new dimensions are associative, non-associative, or exploded. |
DIMASZ |
Sets the size of the dimension arrowheads. |
DIMATFIT |
Determines arrangement of dimension text and arrows when space does not allow both within the extension lines. |
DIMAUNIT |
Controls the unit format for angular dimensions. |
DIMAZIN |
Controls the display of leading and trailing zeros for angular dimensions in decimal format. |
DIMBLK |
Substitutes a user-specified block instead of the arrowheads for both ends of a dimension line. To reset the value of DIMBLK to the default, set it to a single period ("."). |
DIMBLK1 |
Substitutes a user-specified block instead of the arrowhead for the first end of the dimension line. To reset the value of DIMBLK1 to the default, set it to a single period ("."). |
DIMBLK2 |
Substitutes a user-specified block instead of the arrowhead for the second end of the dimension line. To reset the value of DIMBLK2 to the default, set it to a single period ("."). |
DIMCEN |
Controls the display of center marks and center lines for circles and arcs. A value of 0 turns center marks and lines off. |
DIMCLRD |
Controls the ability for you to change the color of the dimension lines, leader, and arrowheads. |
DIMCLRE |
Sets colors for dimension extension lines. |
DIMCLRT |
Sets colors for dimension text. |
DIMDEC |
Sets the number of decimals displayed for tolerances in dimensions. |
DIMDLE |
Controls the distance beyond the extension line that the dimension line extends when using dimension lines with oblique strokes. |
DIMDLI |
Controls the spacing offset of the dimension lines when drawing baseline dimensions. |
DIMDSEP |
Determines the character that is used as a decimal separator when creating dimensions in decimal format. |
DIMEXE |
Determines how far extension lines stretch beyond dimension lines. |
DIMEXO |
Controls the amount of space between the entity being dimensioned and the extension line. |
DIMFIT |
This system variable is no longer required; it is included for compatibility reasons only. |
DIMFRAC |
Sets the fraction format when DIMLUNIT is set to 4 (Architectural) or 5 (Fractional). |
DIMFXL |
Not implemented. Required for .dwg file compatibility only. |
DIMFXLON |
Not implemented. Required for .dwg file compatibility only. |
DIMGAP |
Controls the amount of space before and after the dimension text and the closest end of the dimension line. |
DIMJOGANG |
Not implemented. Required for .dwg file compatibility only. |
DIMJUST |
Sets the horizontal position of the dimension text to one of the following options: centered (0, the default value); next to the first extension line (1); next to the second extension line (2); perpendicular to the first extension line (3); perpendicular to the second extension line (4). |
DIMLAYER |
Not implemented. Required for .dwg file compatibility only. |
DIMLDRBLK |
Specifies the arrow type for leaders. |
DIMLFAC |
Specifies the scale factor for linear dimensions. |
DIMLIM |
Generates dimensions as upper and lower tolerance limits. |
DIMLTEX1 |
Not implemented. Required for .dwg file compatibility only. |
DIMLTEX2 |
Not implemented. Required for .dwg file compatibility only. |
DIMLTYPE |
Not implemented. Required for .dwg file compatibility only. |
DIMLUNIT |
Sets units for all dimension types, except Angular. |
DIMLWD |
Sets the lineweight for dimension lines. |
DIMLWE |
Sets the lineweight for extension lines. |
DIMPOST |
Specifies the prefix and/or suffix that appears in dimension text. |
DIMRND |
Allows you to round off dimension measurements to the specified value. |
DIMSAH |
Controls the display of arrowhead blocks for dimensions. |
DIMSCALE |
Controls the scale factor for variables affecting dimensioning size, distance, and offset. |
DIMSD1 |
Toggles on or off the display of the first dimension line. |
DIMSD2 |
Toggles on or off the display of the second dimension line. |
DIMSE1 |
Toggles on or off the display of the first extension line. |
DIMSE2 |
Toggles on or off the display of the second extension line. |
DIMSHO |
Controls the update of dimension measurements while increasing or decreasing the size of a dimensioned entity. |
DIMSOXD |
Toggles on or off the placement of dimension lines outside the extension lines. |
DIMSS |
Not implemented. Required for .dwg file compatibility only. |
DIMSSPOS |
Not implemented. Required for .dwg file compatibility only. |
DIMSTYLE |
Controls the ability for you to list the available dimension styles and apply a new style from those available. |
DIMTAD |
Determines the vertical placement of dimension text in relation to the dimension line. The default value (0) centers the dimension text between the dimension lines. With other values, you can place the dimension text above or below the dimension line. |
DIMTDEC |
Controls the ability for you to specify the number of decimal places to display tolerance values in a dimension. |
DIMTFAC |
Specifies the scale factor used to calculate the text height of fractions and tolerance values of dimension text. |
DIMTFILL |
Not implemented. Required for .dwg file compatibility only. |
DIMTFILLCLR |
Not implemented. Required for .dwg file compatibility only. |
DIMTIH |
Positions dimension text inside the extension lines either horizontally (on) or aligned with the dimension line (off). |
DIMTIX |
Positions dimension text between extension lines. |
DIMTM |
Specifies the minimum tolerance or lower limit value for dimension text. |
DIMTMOVE |
Determines how dimension text is moved. |
DIMTOFL |
Toggles on or off the drawing of a dimension line between the extension lines when text is placed outside the measured points. |
DIMTOH |
Sets the placement of dimension text outside the extension lines. The default value (1) draws text horizontally. Changing the value to off (0) aligns text with the dimension line. |
DIMTOL |
Appends plus and minus tolerance values to dimension text. |
DIMTOLJ |
Not implemented. |
DIMTP |
Specifies the maximum tolerance or upper limit value for dimension text. |
DIMTSZ |
Determines the size of the oblique strokes drawn, replacing the arrowheads in linear, radius, and diameter dimensioning. |
DIMTVP |
Sets the vertical position of dimension text relative to the dimension line. |
DIMTXSTY |
Specifies a new value for the dimension text style. |
DIMTXT |
Specifies the height of dimension text. If the current text has a fixed height, DIMTXT does not override this setting. |
DIMTXTDIRECTION |
Determines the dimension text direction. |
DIMTZIN |
Determines the suppression of leading and trailing zeros in tolerance values of dimensions. |
DIMUNIT |
This system variable is no longer required; it is included for compatibility reasons only. |
DIMUPT |
Controls the option for you to control the dimension line location only or both the dimension line location and the text position. |
DIMZIN |
Determines the suppression of leading and trailing zeros in primary dimension text. |
DISABLEDIGITALSIG |
Determines whether the digital signature feature is enabled in IntelliCAD. |
DISPSILH |
Not implemented. |
DISTANCE |
Saves the distance calculated by DIST. |
DONUTID |
Specifies the default value for the inside diameter of a donut. |
DONUTOD |
Specifies the default value for the outside diameter of a donut. |
DRAGDETAIL |
Controls the level of detail that displays during dragging. |
DRAGMODE |
Controls the display of entities as you drag them. When set to on, DRAGMODE displays an outline of the entities as you drag them. |
DRAGMOVE |
Determines whether entities can be moved by dragging the mouse. |
DRAGOPEN |
Inserts or opens a drawing file that has been dragged from the desktop onto the drawing area. |
DRAGP1 |
Not implemented. Required for .dwg file compatibility only. |
DRAGP2 |
Not implemented. |
DRAGVS |
Not implemented. Required for .dwg file compatibility only. |
DRAWINGTYPE |
Stores the type of drawing that is active. |
DTEXTED |
No longer used and replaced by TEXTED. |
DWFFRAME |
Determines whether DWF frames are visible and printed. |
DWFOSNAP |
Determines whether entity snapping is turned on or off for .dwf files that are attached to drawings. |
DWGCHECK |
Not implemented. Required for .dwg file compatibility only. |
DWGCODEPAGE |
Specifies the code page for the drawing. |
DWGNAME |
Stores the drawing name. |
DWGPREFIX |
Stores the full path for the drawing. |
DWGTITLED |
Stores data indicating whether the current drawing has been named. |
DWGUNITSIN1SVGPIXEL |
Determines the number of drawing units in one .svg pixel when a drawing file is exported to an .svg file. |
DWGWORKSPACE |
Stores the name of the workspace that is activated when opening or creating a .dwg drawing. |
DWTSHEETSETPATH |
Sets the default path for storing .dwt files used as templates for new sheets when added to a sheet set. |
DXEVAL |
Not implemented. Required for .dwg file compatibility only. |
DYNDIGRIP |
Determines which dynamic dimensions are enabled when editing entities using grips. |
DYNDIVIS |
Determines the number of dynamic dimensions that display when editing entities using grips. |
DYNMODE |
Controls dynamic input features. |
DYNPICOORDS |
Determines whether pointer input uses absolute or relative coordinates for second and next points. |
DYNPIDISPMODEBOX |
Determines whether @ or # symbols display for coordinates of second and next points during pointer input. |
DYNPIFORMAT |
Determines which coordinate system format is used during pointer input for specifying second and next points. |
DYNPIVIS |
Determines when coordinate tooltips display for pointer input. |
DYNPROMPT |
Turns on or off the display of command prompts in dynamic input tooltips. |
DYNSHOWDEFAULT |
Turns on and off the display of current values in dynamic input fields. |
DYNUSEANGBASE |
Determines whether the ANGBASE system variable is used when you specify an angle while using dynamic input. |
GEOLATLONGFORMAT |
Sets the unit of measurement for latitude and longitude. |
GEOMARKERVISIBILITY |
Controls the visibility of geolocation markers. |
GEOMARKPOSITIONSIZE |
Sets the scale factor used for point indicators and multiline text entities when creating position markers. |
GFANG |
Sets the angle of the gradient pattern. |
GFCLR1 |
Specifies the default color assigned to gradient patterns that have only one color or to the first color of gradient patterns that have two colors. |
GFCLR2 |
Specifies the default color assigned to the second color of gradient patterns that have two colors. |
GFCLRLUM |
Specifies the tint and shade of gradient patterns that have only one color. |
GFCLRSTATE |
Specifies whether the default gradient pattern is defined by one color or two colors. |
GFNAME |
Specifies the type of gradient pattern. |
GFSHIFT |
Specifies how the gradient pattern is positioned. |
GRAVITYSNAP |
Controls whether the cursor always snaps to the nearest entity snap point when AutoSnap magnet is turned on. |
GRDRAWPACKAGESIZE |
Sets the maximum buffer size for data caching when using the sds_grdraw function. |
GRIDCOLOR |
Determines the dot grid color. |
GRIDCOLORMAJOR |
Determines the color of major grid lines. |
GRIDCOLORMAJORBEDITOR |
Determines the color of major grid lines in the Block Editor. |
GRIDCOLORMINOR |
Determines the color of minor grid lines. |
GRIDCOLORMINORBEDITOR |
Determines the color of minor grid lines in the Block Editor. |
GRIDDISPLAY |
Determines how the grid displays. |
GRIDMAJOR |
Determines the number of major grid lines compared with minor grid lines. |
GRIDMODE |
Toggles the grid on or off. |
GRIDPOINTSMAX |
Determines the maximum number of grid points to display. |
GRIDSTYLE |
Controls the areas where a dotted grid displays. |
GRIDUNIT |
Stores in the .dwg file the x and y grid spacing for the active viewport. |
GRIPBLOCK |
Determines whether only one grip point for a block displays or if the grip points for all the entities in the block display. For example, the value 0 assigns a grip to only the block's insertion point. The value 1 assigns grips to all entities in the block. |
GRIPBYKEYBOARD |
Controls whether grip editing is available using the keyboard. |
GRIPCOLOR |
Determines the color of unselected grips. |
GRIPDYNCOLOR |
Not implemented. Required for .dwg file compatibility only. |
GRIPHOT |
Determines the color of selected grips. |
GRIPHOVER |
Determines the fill color of unselected grips when the cursor pauses over them. |
GRIPOBJLIMIT |
Turns off the display of selection set grips when the selection set includes more than the specified number of entities. |
GRIPS |
Toggles on and off the use of selection set grips. |
GRIPSIZE |
Saves the size of the box (in pixels) used to display grips. |
GRIPTIPS |
Determines whether grip tips for dynamic blocks (not implemented) and custom objects display when the cursor pauses over them. |
GROUPDISPLAYMODE |
Determines how grips display when a group is selected. |
GROUPFRAMECOLOR |
Determines the color of the frame displayed when advanced group grips are turned on. |
GROUPMAX |
Specifies the number of groups that can display in IntelliCAD Explorer and the Group dialog box. |
GSDEVICEMODE |
Sets the preferred graphics device to use in the program. |
GSUSEDDEVICEMODE |
Displays the currently used graphics device. |
GTAUTO |
Not implemented. |
GTDEFAULT |
Not implemented. |
GTLOCATION |
Not implemented. |
HALOGAP |
Sets the size of a gap that displays in 2D wire-frame view when one entity overlaps another entity. |
HANDLES |
Indicates whether handles are being used in the drawing. |
HANDSEED |
Stores the value for the next available handle name. |
HELPPREFIX |
Stores the location where the help system is located. |
HIDEPRECISION |
Determines the level of precision when viewing a drawing as a hidden-line image or shaded image in wire-fame view. |
HIDETEXT |
Determines whether single line and multiline text entities become hidden during the HIDE command. |
HIDEXREFSCALES |
Determines whether scales contained in external references display in the annotative scale list for the current drawing. |
HIGHLIGHT |
Toggles entity highlighting on or off. |
HIGHLIGHTCOLOR |
Determines the color for highlighting. |
HIGHLIGHTLIMIT |
Controls the number of selected entities (and subentities) that will be shown as highlighted over regular entities. |
HPANG |
Sets the angle of the hatch pattern. |
HPANNOTATIVE |
Determines whether new hatch patterns are annotative. |
HPASSOC |
Controls the associativity of new hatch patterns and gradient fills. |
HPBACKGROUNDCOLOR |
Determines the default background color for newly created hatch patterns. |
HPBOUND |
Determines whether a new boundary is created as a region or polyline. |
HPDOUBLE |
Determines whether cross-hatching is on or off. |
HPDRAWORDER |
Determines the order in which hatches and fills are drawn. |
HPGAPTOL |
Sets the gap tolerance for closed boundaries during hatch creation. |
HPINHERIT |
Controls the hatch origin when hatch properties are inherited. |
HPISLANDDETECTION |
Determines how islands are detected when creating boundaries from polylines. |
HPISLANDDETECTIONMODE |
Controls whether islands are detected when creating boundaries from polylines. |
HPMAXLINES |
Determines the maximum number of hatch lines. |
HPNAME |
Stores the default hatch pattern name. |
HPOBJWARNING |
Stores the number of entities that can be selected before a warning message displays when creating hatches. |
HPORIGIN |
Sets the hatch origin point in the current UCS. |
HPORIGINMODE |
Controls the default hatch origin point. |
HPPREVIEW |
No longer used and replaced by HPQUICKPREVIEW. |
HPQUICKPREVIEW |
Controls whether the hatch pattern displays in the drawing for selected entities while choosing options in the Boundary Hatch dialog box. |
HPSCALE |
Stores the default scale factor for hatch patterns. |
HPSEPARATE |
Stores whether a single hatch entity or separate, multiple hatch entities are created when more than one closed boundary is selected for hatch creation. |
HPSPACE |
Designates the line spacing in user-defined hatch patterns. |
HPSTYLE |
Determines the hatch pattern style. |
HPTRANSPARENCY |
Specifies the default transparency for new hatches and fills. |
HYPERLINKBASE |
Defines the relative path used for all hyperlinks in the current drawing. |
HYPERLINKRELATIVE |
Turns on or off the use of a relative path for an entity's hyperlink. |
HYPERLINKTOOLTIP |
Turns on and off the display of tooltips that display for entities with hyperlinks assigned. |
LASTANGLE |
Stores the angle value for the last line segment created relative to the current user coordinate system (UCS). |
LASTPOINT |
Stores the value of the last point entered relative to the current user coordinate system (UCS). |
LASTPROMPT |
Stores the last prompt string displayed on the command line. |
LATITUDE |
Stores the value of the geographic marker's latitude. It is always represented in decimal degrees. |
LAYERCONTROLFILTER |
Controls whether the layer filter selected in the Explorer is applied to the list of layers displayed
on the Home tab of the ribbon (if the ribbon is available for your program version) and on the Entity Properties toolbar.
|
LAYERCONTROLSIZE |
Sets the width of the layer name control on the ribbon in pixels. |
LAYEREVAL |
Not implemented. Required for .dwg file compatibility only. |
LAYERINVERTFILTER |
Determines whether the currently selected filter is inverted, or reversed. |
LAYERNOTIFY |
Not implemented. Required for .dwg file compatibility only. |
LAYLOCKFADECTL |
Specifies the fade percentage applied to entities that are located on locked layers. |
LAYOUTCREATEVIEWPORT |
Controls whether a layout viewport is created automatically for each new layout that is added to a drawing. |
LAYOUTREGENCTL |
Controls how drawings are regenerated when switching between the Model tab and Layout tabs. |
LAYOUTTAB |
Controls the display of the Model and Layout tabs. |
LEGACYCTRLPICK |
Not implemented. |
LENGTHENOLDCOMPAT |
Determines how segments of open-ended entities are lengthened during the Edit Length command. |
LENSLENGTH |
Stores the lens length in millimeters used in the active viewport when perspective is on. |
LIGHTGLYPHDISPLAY |
Determines whether light icons display in the drawing. |
LIGHTINGUNITS |
Not implemented. Required for .dwg file compatibility only. |
LIGHTLISTSTATE |
Not implemented. |
LIGHTSINBLOCKS |
Not implemented. Required for .dwg file compatibility only. |
LIMCHECK |
Controls whether you can create entities outside the drawing limits. |
LIMMAX |
Saves the upper-right drawing limits for the active workspace. |
LIMMIN |
Saves the lower-left drawing limits for the active workspace. |
LINEARBRIGHTNESS |
Not implemented. Required for .dwg file compatibility only. |
LINEARCONTRAST |
Not implemented. Required for .dwg file compatibility only. |
LINESMOOTHING |
Determines whether line smoothing (anti-aliasing) is turned on or off for entities in 2D visual styles. |
LISPAUTOREDRAWFREQ |
Sets the frequency of automatic view update during LISP operations [Hz]. |
LISPINIT |
Determines whether the LISP environment is re-initialized when a new drawing is created or opened. |
LISPPATH |
Stores the path used to locate user defined LISP files. |
LOCALE |
Displays the Windows locale setting. |
LOCALEROOTPREFIX |
Displays the name of the folder, including the full path, where customizable files are installed. |
LOCKUI |
Determines whether the position of toolbars is locked. |
LOFTANG1 |
Determines the draft angle for the first cross section when creating lofted entities. |
LOFTANG2 |
Determines the draft angle for the last cross section when creating lofted entities. |
LOFTMAG1 |
Determines the draft angle magnitude for the first cross section when creating lofted entities. |
LOFTMAG2 |
Determines the draft angle magnitude for the last cross section when creating lofted entities. |
LOFTNORMALS |
Determines how the surfaces are created for a new loft entity. |
LOFTPARAM |
Determines various options that are used when creating lofted entities. |
LOGEXPBRIGHTNESS |
Not implemented. Required for .dwg file compatibility only. |
LOGEXPCONTRAST |
Not implemented. Required for .dwg file compatibility only. |
LOGEXPDAYLIGHT |
Not implemented. Required for .dwg file compatibility only. |
LOGEXPMIDTONES |
Not implemented. Required for .dwg file compatibility only. |
LOGEXPPHYSICALSCALE |
Not implemented. Required for .dwg file compatibility only. |
LOGFILEMODE |
Toggles whether the commands executed in the program are maintained in a log file or not. |
LOGFILENAME |
Sets the file name for the log file. |
LOGFILEPATH |
Sets the location of the log file. |
LOGFONTSERVICE |
Determines whether information about font substitution is added to the default log file. |
LOGINNAME |
Displays the name of the registered user. |
LONGFNAME |
Toggles on and off the support for long file names. |
LONGITUDE |
Stores the value of the geographic marker's longitude. It is always represented in decimal degrees. |
LTGAPSELECTION |
Not implemented. Required for .dwg file compatibility only. |
LTSCALE |
Sets the default linetype scale factor. |
LTSCLWBLK |
Determines whether the global linetype scale will be applied to an inserted block. |
LTYPEGEN |
Controls the display of linetypes. When turned on (set to 1, the default), linetypes are regenerated. |
LUNITS |
Sets the default linear units. You can set the value to one of the following: 1=Scientific, 2=Decimal, 3=Engineering, 4=Architectural, 5=Fractional. |
LUPREC |
Controls the number of decimal places shown for coordinate display and linear units in commands. |
LWDEFAULT |
Defines the default lineweight. |
LWDISPLAY |
Controls whether lineweights display. |
LWPOLYOUT |
Controls whether the program converts normal polylines to lightweight polylines when saving a drawing file. The default value (1) converts polylines to lightweight polylines. Changing the value to 0 specifies that polylines will not convert to lightweight polylines. |
LWUNITS |
Controls whether lineweights are assigned in millimeters or inches. |